Source: https://doer.ee/gpio/ Snapshot date: 2026-11-15 Original claims/examples below are archival, not verified guidance. Menu Features Specs GitHub Buy Now Features Specs GitHub Buy Now 💻 Cross-Platform Works on Windows, macOS, and Linux. No special drivers required. Raspberry Pi API Compatible with Raspberry Pi system. Same API calls you already know. ⚡ Digital / PWM / ADC Full GPIO with pull-up/pull-down, hardware PWM on 8 pins, and analog input on 8 pins. 🔓 Open Source Python library and STM32 firmware are GPL-3.0 licensed and publicly available on GitHub. Get Started: Control GPIO from Python Plug the board in via USB, install the Python library, and you're ready to control hardware from any Python script — on any computer. The board auto-detects over USB, so no manual port configuration is needed. Install in one command pip install DoerGPIO (On some systems you may need to use pip3 instead of pip , or specify the full path (e.g. python -m pip install DoerGPIO ) if pip is not on your PATH.) Python 3.9+ supported Auto-detection via USB identification — no serial port setup # Control an LED with DoerGPIO import DoerGPIO as GPIO import time # Setup pin 17 as output GPIO. setmode (GPIO.BCM) GPIO. setup ( 17 , GPIO.OUT) # Blink 5 times for _ in range ( 5 ): GPIO. output ( 17 , GPIO.HIGH) time. sleep ( 0.5 ) GPIO. output ( 17 , GPIO.LOW) time. sleep ( 0.5 ) GPIO. cleanup () Board Capabilities Digital I/O All GPIO pins support configurable pull-up and pull-down resistors. Use any pin as a digital input or output. GPIO.setup(pin, GPIO.IN / GPIO.OUT) pull_up_down=GPIO.PUD_UP / GPIO.PUD_DOWN GPIO.input(pin) / GPIO.output(pin, val) PWM Output Hardware PWM on 8 dedicated pins. Control servo motors, LED brightness, motor speed, and more. PWM Pins 4 · 9 · 10 · 16 · 18 · 20 · 22 · 26 Analog Input (ADC) Read analog sensors — potentiometers, light sensors, temperature sensors — on 8 ADC-capable pins. ADC Pins 0 · 9 · 10 · 11 · 14 · 15 · 18 · 26 Technical Specifications Built around the STM32F070C6TX microcontroller, the Doer USB GPIO Board delivers reliable, real-time hardware control over standard USB. The firmware is written in C using STM32CubeIDE and fully open source. STM32-based for real-time, deterministic performance Plug-and-play — board auto-identifies over USB Firmware source code available on GitHub (GPL-3.0) Microcontroller STM32F070C6TX USB Type USB Full Speed (CDC) GPIO Pins 28 configurable pins PWM Pins 8 pins — 4, 9, 10, 16, 18, 20, 22, 26 ADC Pins 8 pins — 0, 9, 10, 11, 14, 15, 18, 26 Pull Resistors Configurable pull-up / pull-down on all pins Platforms Windows · macOS · Linux Python Version 3.9+ Python Library pip install DoerGPIO Firmware Language C (STM32CubeIDE) License GPL-3.0 Who It's For 🔧 Makers & Hobbyists Build hardware projects from your laptop without needing a Raspberry Pi. Control LEDs, motors, and sensors directly from Python. 🧪 Rapid Prototyping Test hardware interactions from your development machine. Iterate faster by scripting GPIO changes directly in Python. 🎓 Education & Teaching Teach embedded systems and GPIO concepts with familiar Python syntax. Works on any classroom computer over USB. Get Started in Minutes 1 Install the Python Library pip install DoerGPIO 2 Connect the Board via USB Plug the Doer USB GPIO Board into any USB port. It auto-identifies itself — no manual serial port selection or driver installation required on Windows, macOS, or Linux. 3 Run Your First Script import DoerGPIO as GPIO GPIO. setmode (GPIO.BCM) # Pin 17 as output GPIO. setup ( 17 , GPIO.OUT) GPIO. output ( 17 , GPIO.HIGH) # Pin 22 as input with pull-up GPIO. setup ( 22 , GPIO.IN, pull_up_down=GPIO.PUD_UP) value = GPIO. input ( 22 ) print ( f"Pin 22: {value}" ) GPIO. cleanup () # Reset all pins How to Update Firmware 1 Install the Upload Tool Dependency pip install pyserial 2 Download the Firmware & Upload Script Get the latest .bin firmware file and upload_fw.py from the GitHub releases page. GitHub Releases → 3 Run the Upload Script Make sure the board is unplugged , then run the script. When prompted, plug in the board and flashing will begin automatically. If the board is already connected when the script starts, it will ask you to unplug it first. python3 upload_fw.py DoerGPIO_FW.bin Frequently Asked Questions Which operating systems are supported? ↓ The board works on Windows, macOS, and Linux. It communicates over standard USB CDC (serial), so no special drivers are required on most modern systems. How do I install the Python library? ↓ Run pip install DoerGPIO in your terminal. Python 3.9 or higher is required. The library auto-detects the board over USB, so no manual port selection is needed. Which pins support PWM and ADC? ↓ PWM pins: 4, 9, 10, 16, 18, 20, 22, 26. ADC pins: 0, 9, 10, 11, 14, 15, 18, 26. All pins support standard digital I/O with configurable pull-up and pull-down resistors. Is the firmware open source? ↓ Yes. Both the Python library and STM32 firmware are released under the GPL-3.0 license. You can find the source on GitHub: Python Library and Firmware . Where can I buy the board? ↓ The Doer USB GPIO Board is available in our online store. Click here to view the product page and purchase. Ready to Get Started? Control hardware from any computer. One USB cable. Pure Python. Buy Now View Docs on GitHub → USB GPIO Board · Open Source Firmware · Python Library GitHub Firmware GitHub Python Lib Product Page © 2026 DOER WORKS. ALL RIGHTS RESERVED.